| When you think about chemical ,coatings,polyurea,spray, what do you think of first? Which aspects of chemical ,coatings,polyurea,spray are important, which are essential, and which ones can you take or leave? You be the judge.
You may not consider everything you just read to be crucial information about chemical ,coatings,polyurea,spray. But don't be surprised if you find yourself recalling and using this very information in the next few days.
Polyurea is a coating, lining and joint sealant technology. It is being used successfully for any different applications today. Polyurea coatings and linings are more commonly applied over concrete and steel for corrosion protection and abrasion resistance. They also have tremendous advantages over conventional materials for joint fill and caulk applications due to their fast set nature, high elongation and durability/abrasion characteristics. Polyurea can be molded and shaped by spraying it into molds. Similarly, polyurea is also used as hard coat protective shell over expanded polystyrene (EPS) for architectural molded fascia applications. The markets and applications are endless and on the rise.
Ultimate Linings UL KG 8012 is a fast setting, rapid curing, 100% solids, flexible, aliphatic, color stable, two component spray polyurea ,that can be applied to suitably prepared interior or exterior concrete and metal surfaces. Its extremely fast gel time makes it suitable for applications down to -20°F. It may be applied in single or multiple applications without appreciable sagging and is relatively insensitive to moisture and temperature allowing application in most temperatures.
FEATURES
*Excellent Color Retention
*Excellent Thermal Stability / Zero VOC
*No Toxic Vapors & Odorless
*Meets USDA Criteria with Low Permeance Rate
*Low Temperature Flexibility / Non-Reactive
*Good Chemical Resistance
*100% Solids
*Interior or Exterior Applications
*Coats Most Metals without Primer
*Installed With or Without Reinforcement in Transitional Areas
*Seamless
*Zero VOC
TYPICAL
Airports, Power Plants, Refineries, Structural
Steel, Food Processing Plants, Fertilizer Plants,
Mining Operations, Cold Storage Facilities
Marine Environments, Paper and Pulp Mills,
Parking Garage Decks, OEM, Walkways & Balconies
Water and Waste Water Treatment, Industrial and
Manufacturing Facilities.
COLORS
Clear/Neutral. Custom colors are available upon request. Color Packs, when used, must be added to Part-B.
SURFACE PREPARATION
In general, coating performance and adhesion are directly proportional to surface preparation. Most failures in the
performance of surface coatings can be attributed to poor surface preparation. Polyurea coatings rely on the structural
strength of the substrate to which they are applied. All surfaces must be free of dust, dirt, oil, grease, rust, corrosion and
other contaminants. When coating substrates previously used, it is important to consider the possibility of substrate
absorption, which may affect the adhesion of the coating system, regardless of the surface preparation. Ultimate Linings
recognizes the potential for unique substrates from one project to another.
Brass and Copper:
Brass and copper should be blasted with sand, and not with steel or metal grit. Remove all dust and grease prior to applying primer.
Galvanized Surfaces:
Clean and degrease any contaminated surfaces before priming. Do not blast galvanized surfaces with an abrasive grit. An adhesion test is recommended prior to starting the project.
Fiberglass Reinforced Plastic:
The gel coat should be lightly blasted or sanded with 80 grit sandpaper and cleaned.
Plastic Foams:
Enhanced adhesion is obtained when the foam is mechanically abraded. When coating polystyrene, do not use a solvent-based primer.
Textiles, Canvas, Fabrics:
Adhesion to most fabrics, geothermal membranes and textiles does
not require a primer.
Stainless Steel:
Stainless steel may be grit blasted and degreased before priming. Some stainless steel alloys are so inert that it is not possible to achieve a satisfactory bond. An adhesion test is recommended prior to starting the project.
For More Information:- Ultimate Linings, LTD
6630 Roxburgh Ave #175
Houston, TX 77041
Contact no:-713.466.0302
Fax No. : 713.937.0052
Web Site:-http://www.ultimatelinings.com |
Article Details